A long time ago my father’s oldest boyhood friend, Reid Higgins, presented him with a hand-carved wooden sign painted green with gilded letters in beveled quarterboard font that said “C H U R B U C K” surmounted by a rampant, gilded eagle facing “dexter” (or to the right.) For as long as I can remember it has been screwed into the southern side of the house’s front porch. It used to be a fall ritual during Columbus Day weekend to unscrew the eagle and sign and store it indoors for the winter. Since 1991, when I’ve lived in the house year round, the sign has stayed outdoors year round too. And lately it’s been showing a lot of wear and tear.
It has been cleaned up, re-gilded and re-painted, at least two times I know of, in the past forty or fifty years. My grandmother asked a local woman who restored picture frames to do it once, and Reid himself took it back to spruce it up a long time ago. A few weeks ago, on an impulse, I took it down and into the shop. It was much worse than I thought it would be. Other than a few shreds, almost all of the gilt had flaked off. The name board had barely any paint left on it with white primer dominating what was left of the weatherbeaten green.
This is how I brought it back to life for whomever gets to do it next time. It was a lot of fun, I learned something new and cool, and it kept me from going crazy over the frozen holidays.
I took a light wire brush wheel and a cordless Dremel and got most of the flaking paint off without over scouring the mahogamy Reid used to carve the eagle. The detailed feathering and layering of his carving is exquisite and I didn’t want to sand it down or otherwise dull the sharp definition of the plumage. I went over it quickly with the Dremel, then fine steel, followed by a light layer of paste paint remover. The paint on the top edge of the eagle wings, the crown of its head, and top of its beak was long gone, and years of sun and water and snow had caused deep grooving to occur in those areas along the grain line. The sign that forms the base was in worse condition, with similar grooving on the top edges and deep splits forming in the end grain on the right and left ends of the Churbuck sign.
After getting off all of the paint remover and washing it all down with mineral spirits, I took a sponge and thinned down some boiled linseed oil with one part of mineral spirits to three parts linseed and swabbed that over the entire bird and base three times, letting each coat sink in and dry overnight for three days.
Then, with a sanding block and 220 grit sandpaper I smoothed everything down and got ready to prime.
I used primer and paint sold by Fine Paints of Europe, the American distributor of Holland’s Hascolac line of paint. I’ve used a lot of this stuff — I painted the entire house myself one year using about $10,000 worth of Hascolac Oborex and knew from their brochure that someday I wanted to restore something with their Brilliant line of enamels. The stuff is not cheap. I spent about $150 on a quart of white primer, a quart of green enamel, and a tin full of Swedish Putty from a local hardware store that carries FPE.
After priming two coats of white, I sanded it and applied a very thin skim coat of Swedish Putty. This is some medieval substance essentially made out of finely ground glass (silica) and oil. It goes on with the blade of a clean putty knife and can be sanded to a glass smooth service with fine sandpaper after it dries. The warnings that came on the tin were of the skull and crossbones severity so I dutifully wore a mask when I sanded the putty smooth. Silicosis is basically “glass lung” and I like my lungs.
I used the putty as a filler to close up the open grain in the wood and repair the deep splits in the end grain. It can be applied to curved surfaces and trim with a sponge soaked in linseed oil, so I did the inside of the carved letters with that method.
I took a long time sanding the Swedish putty obsessively smooth, stepping down from 220 to 400 to 600 grit paper until the surface was immaculate. I hit it with an air gun, cleaned up the workarea to get rid of as much dust as possible and broke out a new Omega brush and the green Brilliant enamel.
The difference between Hascolac paints and other paints are apparent as soon as you dip the first brushload and start painting. I made all my brush strokes in one direction and put the paint on straight up, no thinning, but was very parsimonious about how loaded up I let the brush get with green paint. The coverage is surprising, but the beauty of the paint is how it self-levels and dries into a gleaming, candy apple kind of sheen.
I applied three coats of green, sanding between then with 400 grit paper. I was very happy with the final result and waited for the mails to deliver me my first booklet of 23 ⅓ karat gold leaf, coton gilder gloves and a German squirrel fur gilding brush.
I’ve never gilded before so I wanted a couple gilding videos on YouTube made by custom sign makers. It looked pretty straightforward.
The first thing is to paint everything that will be gilded a bright coat of yellow and tape off everything that won’t be gilded with blue painters tape, using an xActo knife to cut out the carved letters. I used a little bottle of yellow Testors paint and covered the bird and all the letters with a single coat. Why yellow? That coat, called the TK coat, acts as a radiant substrate for the gold which is microscopically thin to the point of translucence. It you want a dark, subdued shine, you gild over dark paint. If you want brilliance you first must put down some thing light and bright.
Gilding was pretty simple. First I painted some gilding glue over the surface to be gilded. The stuff goes on a little thick and viscous and is a light tinge of blue when applied. After 30 minutes the blue disappears and the gilding glue is tacky and ready for the gold leaf. Tug a wax paper page out of the little booklet of gold, flip it gold side down over the surface coated with gilding glue, and brush very gently with the squirrel brush. I found that a straight tapping of the brush worked best, pushing the leaf down to adhere to the glue and lifting it off the paper backing.
I didn’t want to mess up. Something told me that stripping a botched gilding job would simply suck so I was determined to do it right. Besides, I bought $50 worth of leaf — 40 3”x2” sheets f– and used about three quarters of it. After the gilding goes down, one just looks for the yellow under paint and dabs a little more gold leaf on it, until everything to be gilded is covered with a layer of gold and fuzzy with loose flakes. Flick it and smooth it with the gilding brush, burnish it with a finger tip in the white cotton gilding glove, and we’re talking a very expensive rainy day project for the kindergarten class.
I cleaned up the lettering with a very fine modeling brush and the green enamel. Then I coated all of the bird and the lettering with two thin coats of shellac to protect the gold from the elements.
And here is the final result.
In another post I’ll talk more about the man who carved the sign, Reid Higgins, and his amazing carvings of local shore birds.